International Primocon Primer 2,5Lt #458COL654

International Primocon Primer 2,5Lt #458COL654
  • International Primocon Primer 2,5Lt #458COL654
  • International Primocon Primer 2,5Lt #458COL654

International Primocon Primer 2,5Lt #458COL654

International Primocon Primer 2,5Lt
Price:
€80.03
Listing:
€106.71
You Save:
€26.68 (25%)

Description

Primocon conventional underwater primer. Tar-free, quick drying conventional primer for all substrates underwater. Also suitable as a barrier/sealer coat over incompatible or unknown antifoulings. We suggest to apply 1-5 coats. Theory yeld 8,33 mq/lt. Specific weight 1,1. Minimum coating time 3 hours with 23° C (for Micron Optima 11 hours). The suggest thinner is No.3 Thinner, our code COL652. Pack 2,5 lt. Color: gray.


Primocon is a conventional underwater primer. Tar­free, quick drying conventional one­ part primer for all substrates underwater. Can be used under all International antifoulings or as a barrier/sealer coat over incompatible or unknown antifoulings. 

* Primocon prevents leaching of TBT from an underlying antifouling coating provided it is applied at a minimum dry film thickness of 80 microns (minimum 2 coats by roller) & that the film remains intact.

PRODUCT INFORMATION
Colour YPA984­ Grey
Finish Matt
Specific Gravity 1.1
Volume Solids 33%
Typical Shelf Life 2 yrs
VOC (As Supplied) 584 g/lt
Unit Size 2,5Lt

APPLICATION AND USE

Preparation: Wash all surfaces except STEEL with Super Cleaner. 
BARE GRP: Sand using 180­220 grade (grit) paper. 
BARE WOOD/PLYWOOD: Sand smooth with 80­180 and then 280 grade paper. Remove sanding dust by brushing,dusting and wiping. If wiping with solvent then allow to dry completely before applying products recommended for application direct to wood (see specific coating systems).
ALUMINIUM: Degrease with solvent or Super Cleaner. Sand well using 24­120 grit (aluminium compatible) paper.
Coarser grits are recommended to achieve optimum adhesion. Clean thoroughly and allow to dry. Pre­prime using an
International primer as soon as possible (within 8 hours) as detailed for specific coating systems.
ZINC/GALVANISED STEEL: Degrease with solvent or Super Cleaner. Sand well using 60­120 grade paper. Clean thoroughly and allow to dry completely. Pre­prime using an International primer as detailed for specific coating systems.
LEAD: Degrease with solvent or Super Cleaner. Sand well using 120 grade paper or power wire brush. Clean thoroughly and allow to dry. Pre­prime using an International primer as detailed for specific coating systems.
STEEL: Gritblast to Sa 2½ ­ near white metal surface. If gritblasting is not possible, sand the metal surface with 24­36 grit abrasive discs to a uniform, clean, bright metal surface with a 50­75 microns anchor pattern. Use angle grinder on small areas. Pre­prime with Primocon thinned 10­15% with Thinner No.3.

PREVIOUSLY ANTIFOULED SURFACE
In Good Condition: Remove loose material. Wash down with fresh water. Allow to dry. 
In Poor Condition: Remove using Interstrip.
Method_ If filling is required, use appropriate filler after the first coat of Primocon has been applied. Before painting, remove any dust with a dust wipe. Apply the following number of coats: GRP ­ 1, Wood/Plywood ­ 3, Aluminium/Alloy/Zinc/Galvanised Steel/Lead/Steel ­ 5, Barrier/Sealer coat ­ 1.
Tips: Mixing: Stir well before use. Thinner YTA085 Thinners No.3 GTA007. 
Cleaner YTA085 Thinners No.3 
Airless Spray Pressure: 211 bar. Tip Size: 2180­2680. 
Some Important Points: Do not use below 5°C. Do not overcoat with 2­component products. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be 3°C/5°F above dew point and maximum 35°C/95°F. Under certain application conditions it may not be possible to achieve 40 microns dry film thickness in a single coat application. For application to GRP a single coat of Primocon is suitable providing that the dry film thickness is 20 microns or above. For other substrates further coats than that stated should be applied to ensure adequate film thickness is applied for protection of the substrate. Primocon prevents leaching of TBT from an underlying antifouling dry film thickness of 80 microns (minimum of 2 coats by roller).

Compatibility/Substrates: Suitable for all substrates specified.
Number of Coats: 1­5 by brush depending on substrate
Coverage (Theoretical) ­ 8.33 m²/lt
(Practical) ­ 7.4 m²/lt by brush
Recommended DFT per coat 40 microns dry
Recommended WFT per coat 121 microns wet
Application Methods Airless Spray, Brush, Roller

Unit size 0 2,5 lt.
Grey colour.