International Ultra 300 Antifouling 0,75 Lt Red YBB729 #N702458COL630

International Ultra 300 Antifouling 0,75 Lt Red YBB729 #N702458COL630
  • International Ultra 300 Antifouling 0,75 Lt Red YBB729 #N702458COL630
  • International Ultra 300 Antifouling 0,75 Lt Red YBB729 #N702458COL630

International Ultra 300 Antifouling 0,75 Lt Red YBB729 #N702458COL630

Ultra 300 is an antifouling product which offers protection in the highest fouling conditions where a hard, scrubbable antifouling is required. Ideal for fast powerboats.
Price:
€59.90
Listing:
€103.13
You Save:
€43.23 (42%)

Description

Ultra 300 is an antifouling productwhich offers protection in the highest fouling conditions where a hard, scrubbable antifouling is required.

Offers protection in the highest fouling conditions where a hard, scrubbable antifouling is required. Ideal for fast powerboats.
* High strength, hard antifouling
* Hard, scrubbable finish to allow cleaing if needed
* Suitable for sanding to provide a smooth finish
* Smooth finish for maximum glide through the water
* Contains Biolux® technology for sustained antifouling protection

PRODUCT INFORMATION
Colour: YBB729 red
Finish: Matt
Specific Gravity: 1.9 average
Volume Solids: 58% average
Typical Shelf Life: 2 yrs
VOC (As Supplied): 364g/l average
VOC (EU Solvent): 197g/Kg average EU Solvent Emissions Directive (Council Directive 1999/13/EC)
Unit Size: 0,75 Lt

APPLICATION AND USE
Preparation
PREVIOUSLY ANTIFOULED SURFACE
In Good Condition: All fouling and contamination must be thoroughly removed including the leached layer. Use high pressure fresh water wash (3000 psi/207 bar) and/or scraping and wet sanding with typically 80120 grade paper. Do not dry sand. If old antifouling is incompatible or unknown, seal with suitable International Paint barrier/sealer coat.
In Poor Condition: Use Interstrip to remove all traces of antifouling.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP: Prime with Gelshield 200 for osmosis protection, or Primocon or Interprotect.
STEEL/IRON/LEAD/WOOD: Prime with Interprotect or Primocon.

Useful tips:
Mixing: Thoroughly stir until product is mixed to a uniform consistency before use
Thinning: Thinning is not recommended. Antifouling performance can be compromised if correct dry film thickness is not
applied.
Cleaner: YTA085 Thinner No.3
Airless Spray: Pressure: 176210 bar/25003050 psi. Tip size: 517 to 521.
Ventilation and Humidity Control: Ensure adequate ventilation during use.
Other: Antifoulings should only be wet sanded. Never dry sand or burnoff
old antifoulings. True colour will develop after immersion.

Some Important Points
To prevent premature failure, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be 3°C/5°F above dew point and maximum 35°C/95°F.

Compatibility/Substrates
For use over suitably primed GRP, Wood, Steel/Iron and lead.
Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces.
Can be applied direct over most types of antifoulings, provided they are in sound condition, with the exception of VC17m/PTFE antifoulings. Consult your local International Paint representative for specific overcoating advice if you are unsure about compatibility of Ultra 300 over your existing coating scheme.