MORE INFORMATION

PRODUCT DESCRIPTION

Danboline protects bilges, lockers and bulkheads against moisture penetration and wear. Danboline is resistant to oil and fuel spillage and cleans easily.

* Excellent covering power
* Wear resistant
* Available in a range of colours

PRODUCT INFORMATION
Colour YMA100-Grey, YMA101-Red, YMA102-White
Glossy finish
Specific Gravity 5.1
Volume Solids 48% average
Shelf Life 2 years
VOC 411 g / lt
Size 5lt

DRYING / OVERCOATING
Drying
5 ° C (41 ° F) 15 ° C (59 ° F) 23 ° C (73 ° F) 35 ° C (95 ° F)
Dust free 16 hours 8 hours 6 hours 3 hours
Recoating
Substrate temperature
5 ° C (41 ° F) 15 ° C (59 ° F) 23 ° C (73 ° F) 35 ° C (95 ° F)
Covered with Min Max Min Max Min Max Min Max
Danboline 4 days 36 hours 24 hours 3 days 2 days 16 hours 12 hours 1 day

APPLICATION AND USE
Preparation: PREVIOUSLY PAINTED SURFACES
In Good Condition - Wash down with Super Cleaner, rinse with fresh water and let dry. Abrade with 180-280 grit paper.
In Poor Condition: Remove all previous coatings and prime the substrate.

PRIMING: All indications related to the preparation for bare substrates is shown in the data sheets of the appropriate primer.

BARE WOOD. Prime with Yacht Primer or Interprotect.
STEEL. Prime with Yacht Primer or Interprotect.
ALUMINIUM. Prime with Yacht Primer or Interprotect.
GRP. Wash down with Super Cleaner, rinse with fresh water and let dry. Abrade with 180-220 grade paper. Pay particular attention to the surface of molded GRP. It does not require priming.

Method: Sand the primer using 180-280 grade wet or dry. Remove any dust with a tack rag. Apply 1-2 coats.

Tips: Mixing Stir well before using.
Thinner No.1 (Thinner 910 for spray application)
Cleaner Thinner No.1
Ventilation and Humidity Control: Apply in a well ventilated and dry.
Conventional Spray Pressure: 3-4 bar. Nozzle diameter: 1.2 mm. Dilute to about 20% with Thinner 910.

SPRAY APPLICATION - FOR PROFESSIONAL USE ONLY.

For added protection against moisture the surface to treat and to prevent osmosis in the bilges, use Gelshield products.

Important Points
Product temperature should be minimum 15 ° C and maximum 35 ° C.
Ambient temperature should be minimum 5 ° C / 41 ° F and maximum 35 ° C / 95 ° F.
The temperature of the substrate should be minimum 5 ° C / 41 ° F and maximum 35 ° C / 95 ° F.
Compatibility / Substrates Suitable for all substrates specified. Only overcoat with one-component paints.
Number of Coats 1-2
Coverage (Theoretical) 12.3
m² / lt by brush
(Practice) 11.0
m² / lt
DFT. Recommended per coat: 40 microns dry
WFT. Recommended per coat: 82 microns wet
Application Methods: Brush, Conventional Spray, Roller

TRANSPORTATION, STORAGE AND SAFETY INFORMATION

Storage GENERAL INFORMATION:
It is recommended to avoid exposure to air and extremes of temperature. For the full duration of Danboline is realized ensure that, upon storage of the product, the container is firmly closed and the temperature is between 5 ° C / 41 ° F and 35 ° C / 95 ° F. Avoid direct exposure to sunlight.

TRANSPORT:
Danboline should be kept in securely closed containers during transport and storage.

Safety GENERAL:
Read the section on safety label for further information. Information also available from our Technical Help Line.

DISPOSAL:
Do not discard tins or pour paint into water courses; use the facilities provided. And 'to allow paints to harden before disposal.
The residue Danboline can not be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be coordinated with the authorities.

Unit size 5lt.