International Micron 350 Self-polishing Antifouling 750ml Red YBB629 #N702458COL618

International Micron 350 Self-polishing Antifouling 750ml Red YBB629 #N702458COL618
  • International Micron 350 Self-polishing Antifouling 750ml Red YBB629 #N702458COL618
  • International Micron 350 Self-polishing Antifouling 750ml Red YBB629 #N702458COL618

International Micron 350 Self-polishing Antifouling 750ml Red YBB629 #N702458COL618

Micron 350 is self-polishing antifouling that provides 24 months of protection with application of 3-4 coats. Biolux® technology optimizes the biocide power giving an "extra" protection even in areas of high fouling. #N702458COL618
Price:
€69.90
Listing:
€137.21
You Save:
€67.31 (49%)

Description

International Self-polishing Antifouling Micron 350 0.75Lt Red YBB629

Premium Self Polishing Copolymer (SPC) Antifouling.
Micron 350
is an antifouling product effective against fouling organisms; slime, aquatic plants and animals. A Premium Self Polishing Copolymer (SPC) antifouling suitable for professional and consumer application onto vessels in fresh and salt water.
The continuously polishing system provides up to 2 years performance, avoiding paint build up. The ever­smoothing surface ensures that drag is always minimised whilst maintaining optimum biocide release including in stationary periods. Can be applied up to 12 months before launch.

PRODUCT INFORMATION
Finish: Low Sheen;
Specific Gravity: 2.2 average;
Volume Solids: 62% average;
Typical Shelf Life: 2 yrs;
VOC (As Supplied) 333 g/lt.
VOC (EU Solvent): 153g/Kg EU Solvent Emissions Directive (Council Directive 1999/13/EC);
Unit size 0,75 lt.
Colour: YBB629 red.


PREVIOUSLY ANTIFOULED SURFACE
In Good Condition:
All fouling and contamination must be thoroughly removed including the leached layer. Use high pressure fresh water wash (3000 psi/207 bar) and/or scraping and wet sanding with typically 80­120 grade paper. Do
not dry sand. If old antifouling is incompatible or unknown, seal with suitable International Paint barrier/sealer coat.
In Poor Condition: Use Interstrip to remove all traces of antifouling.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP: Prime with Gelshield 200 for osmosis protection, or Primocon or Interprotect.
STEEL/IRON/LEAD/WOOD: Prime with Interprotect or Primocon.

Tips:
Mixing:
Thoroughly stir until product is mixed to a uniform consistency before use
Thinning: Thinning is not recommended. Antifouling performance can be compromised if correct dry film thickness is not applied.
Cleaner: YTA085 International Antifouling Thinner #3.
Ventilation and Humidity Control: Ensure adequate ventilation during use.
Airless Spray (Professional only): Pressure: 176­220 bar/4500­5500 psi. Tip size: 517 to 521.
Other: Antifoulings should only be wet sanded. Never dry sand or burn­off old antifoulings. True colour will develop after immersion.

Some Important Points
To prevent poor results, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be minimum 7°C/45°F and maximum 35°C/95°F.
If you are regularly travelling at high speed (eg 30 knots) you might experience early wear through.
Consult your local International Paint Representative for further advice if you are unsure about the suitability of Micron 350 for your specific requirements.

Compatibility/Substrates
For use over suitably primed GRP, Wood, Steel/Iron and lead.
Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces.
Can be applied direct over most types of antifoulings, provided they are in sound condition, with the exception of VC17m/PTFE antifoulings. Consult your local International Paint representative for specific overcoating advice if you are unsure about compatibility of Micron 350 over your existing coating scheme.

By Brush/Roller:
(Theoretical) ­ 10 m²/L per coat
(Practical) ­ 9 m²/L per coat
By Spray (Professional only):
(Theoretical) ­ 6.67m²/L per coat (for 24 months scheme)
(Practical) – 4m²/L per coat
(for 24 months scheme)
(Theoretical) – 5.17m²/L per coat
(for 12 months scheme)
(Practical) – 3.1m²/L per coat
(for 12 months scheme).