International Ultra 300 Antfouling 0,75Lt Light Blue YBB702 #N702458COL629

International Ultra 300 Antfouling 0,75Lt Light Blue YBB702 #N702458COL629
  • International Ultra 300 Antfouling 0,75Lt Light Blue YBB702 #N702458COL629
  • International Ultra 300 Antfouling 0,75Lt Light Blue YBB702 #N702458COL629

International Ultra 300 Antfouling 0,75Lt Light Blue YBB702 #N702458COL629

International Ultra 300 hard antifouling offers protection in the highest fouling conditions where a hard, scrubbable antifouling is required. Ideal for fast powerboats.
Price:
€59.90
Listing:
€114.78
You Save:
€54.88 (48%)

Description

International Antifouling Ultra 300 0.75Lt Light Blue YBB702

Offers protection in the highest fouling conditions where a hard, scrubbable antifouling is required. Ideal for fast powerboats.
* High strength, hard antifouling
* Hard, scrubbable finish to allow clean-off if needed
* Suitable for burnishing to provide a smooth finish
* Smooth finish for maximum slip through the water
* Contains Biolux® technology for sustained antifouling protection

PRODUCT INFORMATION:
Finish: Matt
Specific Gravity: 1.5
Volume Solids: 45% average
Typical Shelf Life: 2 yrs
VOC (As Supplied): 485 g/lt
Unit Size: 750 ml

DRYING/OVERCOATING INFORMATION
Drying:
5°C (41°F)  15°C (59°F)  23°C (73°F)  35°C (95°F) 
Touch Dry: 1 hrs 45 mins 30 mins 20 mins
Immersion 24 hrs 12 hrs 8 hrs 6 hrs
Note: Max. Immersion Times are as follows: 5-15°C - 3 mths; 23°C - 2 mths; 35°C - 1 mth Overcoating:
Substrate Temperature
5°C (41°F)  15°C (59°F)  23°C (73°F)  35°C (95°F) 
Overcoated By Min Max Min Max Min Max Min Max
Interspeed Ultra 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
Micron 66 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
Micron Extra (Professional) 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext

APPLICATION AND USE:
Preparation: PREVIOUSLY ANTIFOULED SURFACE:
In Good Condition: Rinse with fresh water and allow to dry. If old antifouling is incompatible or unknown, seal with Primocon.
In Poor Condition: Use Interstrip to remove all traces of antifouling.

PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP: Gelshield 200 for osmosis protection, or Primocon.
STEEL/IRON: Prime with Interprotect or Primocon.
LEAD: Prime with Interprotect or Primocon.
WOOD: Prime with Interprotect or Primocon.
Method: Apply two coats per season.

Useful tips: Mixing Stir well before use.
Thinner: YTA085 Thinners No.3
Thinning is not recommended.
Cleaner: YTA085 Thinners No.3
Other: True colour will develop after immersion. Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance to apply the correct thickness.
Some Important Points: To prevent poor results, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum -5°C and maximum 35°C. Ambient temperature should be minimum -5°C and maximum 35°C. Substrate temperature should be minimum 1°C above dew point and maximum 35°C. 

Compatibility/Substrates: GRP, Wood, Steel/Iron, Lead. Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces. Can be applied direct over most types of antifoulings, provided they are in sound condition

Number of Coats 2-3 by brush/roller
Coverage (Theoretical) - 10.5 m²/lt by brush
(Practical) - 9.4 m²/lt by brush
Recommended DFT per coat 43 microns dry
Recommended WFT per coat 96 microns wet
Application Methods: Brush, Roller, AIRLESS SPRAY NOT

Unit size 0.75 lt.
Light Blue colour YBB702.